Self Cleaning Fuel Handling Systems / 3 Phase Industrial Centrifuge

Self Cleaning Fuel Handling Systems / 3 Phase Industrial Centrifuge

Description:

A marine oil separator is mainly used to remove water and mechanical impurities from fuel oil, lubricating oil and other mineral oil in marine diesel engine units and land-used diesel generator units of power stations so as to reduce wear of the diesel engine and other machines and prolong engine life. The model is also used to separate two unsolvable liquids with different specific gravity or remove a small number of solid particles from a liquid. It is divided into a 2phase solid-liquid separator and an oi-water-impurity 3phase separator. They are workable on land and ship, we have the CCS certificate to certify their function and usage. There are different discharge types of oils, manual, partial, fully discharged, variable discharge, etc which depend on the different materials. commonly, we define the capacity as the density of 0#  diesel oil, and we have a chart to help you find out the exact processing capacity of your needs. We not only provide the single oil separator, but also the whole unit containing the pumps, valves, heats, pipes, and so on.

Competitive Advantages:

•  Overload overheat protection
•  High rotating speed,
•  accurate dynamic balancing, 
•  long time with low vibration, 
•  safety and security.
•  CCS certificate
•  Continuous working

Main Technical Specification:

The whole unit consists of:

1. Separator     2. Screw pump    3. Electric control box           4. Steam heater

5. Temperature adjusting valve    6. An integral heat ball valve       7. Steam trap valve       

8. Temperature sensor         9. Pneumatic Three-way valve      10. Stop-check valve     

11. Oil filter       12. Vacuum gauge       13. Pressure gauge      14. Air pressure reducing valve  

15. 3/2 Solenoid valve          16. Ball valve          17. Brass filter ball valve

18. Water pressure reducing valve       19. 2/2 Solenoid valve      20. Pressure switch

21. moisture sensor      22. Skid

Principle and structure

The disc separator is the vertical centrifuge. The drum is installed on the upper side of the vertical shaft. Driven by the motor, it will rotate at a high speed through the gearing. Inside the drum, there is a group of dish parts overlaying each other – a disc. There is a very small gap between the disc. The suspension (or emulsion) is fed into the drum through the inlet in the middle of the drum. When the suspension (or emulsion) flows through the gap between the disc, under the action of the centrifuge, the solid particles (or droplets) go down to the disc in the formation of sediment (or liquid layer). Along the disc surface, the sediment slides out of the disc and accumulates at the part with the largest diameter inside the drum. After the separation, the liquid is discharged out of the drum from the drain outlet. The role of the disc is to reduce the sediment distance of solid particles (or droplets) and enlarge the sediment area of the drum. With the disc inside the drum, the capacity of the separator is improved greatly. The solid gathering inside the drum is manually removed by taking apart the drum after powering off or discharging from the drum through the slag-off part with the separator power on.

Specification:

Condition for mineral oil separation and actual capacity (refer to the chart)

Technical analysis:

Peony's Disc separator technology comparison with foreign companies

Value Analysis:

1. According to the requirements of each classification society, all modules are equipped with oil leak alarms and high-temperature alarms.

2. Oil, hydraulic, and pneumatic control part adopts the Brand Baode (Germany).

3. Heater adopts the brand SWEP (Germany).

4. Pressure control adopts Korean products or products

5. Screw pump is used instead of the gear pump.

6. All equipped with an automatic temperature control device (Made by the RTK production in Germany or made in China).

7. The main electrical components of the standard electrical control boxes are produced by Schneider company while PLC is produced by Siemens or Mitsubishi.

8. The complete sets referred to above are all Peony's production of automatic Standard Controls and we certainly can modify the configuration list according to customers' specified requirements.

Application:

Mineral oil industry: purification of fuel and lubricating oil used on main engine for vessels, land diesel engine, power plants, etc.